If you like going FAST, this is the foil for you! The Neil Pryde RS:Flight F4 Foil is a full carbon beast that comes with two different front wings and a fully adjustable angle rear wing, allowing you to fine tune for the conditions and go as fast as possible in a huge range of wind and water states. Use the larger front wing, and angle the rear wing for max lift in super light wind conditions, and then slowly adjust the rear wing to lower lift angles as the wind comes up. Above 18 or 20 knot winds and you'll want to swap out the front wing for the smaller 590mm option, and hang on, because it is time to break some speed records!
We give this foil a high score for stability, top speed, and wind range. Great bang for the buck with two front wings and the ingenious rear wing angle adjustment system. Get yours today!
Take to the air with the all-new RS:FLIGHT F4 from NeilPryde an experience like nothing else.The RS:FLIGHT F4 foil is a no- compromise, performance carbon foil designed in collaboration with F4 USA. The RS:FLIGHT F4 is an evolution of the proven F4 windsurf hydrofoil design, already considered as the best wind-foil in the market with unmatched hydrodynamics. The RS:FLIGHT F4 has very stiff construction and low drag allowing the rider to use every gust for acceleration. It is delivered with two front wings for two flight modes: the High Lift Wing combines early take off and exceptional upwind performance with amazing stability, while the High Speed Wing delivers maximum speed and acceleration. RS:FLIGHT F4. There's something in the air.
Deep Tuttle Base
Integrated carbon Deep Tuttle Base for maximum strength, elimination of movement and perfect load transfer.
Seven stainless steel bolts for maximum strength to weight ratio while preventing any corrosion problems.
INTEGRATED TAIL-FUSELAGE CONNECTION WITH SCREW-ADJUSTABLE TAIL TRIM ANGLE
This feature minimizes the drag at the end of fuselage and provides a very strong connection through opposing screws countered in tension. There is also +/- 1.5 degree (total 3degree) adjustability available by changing the tension of the front top and bottom screws. Foil is perfectly trimmed for average weight sailor (75-80kg) with tail in neutral position. Heavier sailors, especially with large front wing in light winds or during learning process might prefer slightly more stabilizing force that down tilted rear wing provides. At the same time lighter sailors, especially in strong wind conditions might find a neutral position creates excessive lift and will reduce the differential angle between two wings by tilting the tail slightly up.
SMOOTH RADIUS INTERSECTION POINTS BETWEEN MAST AND FUSELAGE
At the most critical loading stress points (shaft leading and trailing edge-to-fuselage connections), we maintained large radius in the corners. This has a benefit of distributing tremendous compression forces existing in this area while at the same time creating a very smooth shape which minimizes turbulences common to hard edges.
SINGLE PIECE MAST/FUSELAGE T-CONSTRUCTION
Construction of our carbon foil features solid pre-preg carbon fiber layup with continuous unidirectional fibers connecting the shaft (mast) to the fuselage. This is by far the strongest and stiffest connection possible which also allows to keep the shaft and fuselage cross-section minimal, reducing the drag. This construction offers the best strength to weight ratio.
Fuselage is designed with the unique cross-section taper where the maximum volume is concentrated in the areas of highest loads. The thickest section is connecting front wing mounting area to the mast intersection; this is the area that transfers the lift of the foil onto the board and supports the complete weight of the sailor, board and rig.
BLENDED FUSELAGE TO WING CONNECTION
During carving, there can be extreme torsional forces at the fuselage-to-wing connection area.
These forces are created by different lifts on the two sides of the main wing. Part of the wing that is inside the curve experiences lower water velocity and creates lower lift. On the opposite side, the wing sees higher water velocity and creates higher lift; this differential in lifts, particularly extreme when using large wings, results in very high torsional load. To make sure there is adequate strength to support this stress, even with heaviest sailors, we designed a very large and wide connection area. This ‘saddle’ distributes torsion force over a larger area and significantly reduces the torque leverage on the wing screws.
||High Lift Wing Span
||High Speed Wingspan
||High Pressure moulded 100% Carbon Pre-preg
||7.8 pounds / 3.5kg